PCB - JLCPCB Q&A

Dear all, How can I define a V-cut in a Kicad 9 project? Best regards and thank you for your attention, Manuel Ferreira

1 Reply Asked by 22*******8A

Cable and Connector assembly that Plugs into: X1002WVS-03L-HF-LPSN

I have a X1002WVS-03L-HF-LPSN on my board. What is the mating connector? Even better is if there is a mating connector and......

1 Reply Asked by 49*******8A

Environmental Response

Are your PCBs TSCA compliant?

1 Reply Asked by 66*******3A

UL Mark on Flex PCBs (capton)

Can you mark flex PCBs with UL mark?

1 Reply Asked by 57*******4A

94V fire rating certificate?

Hello, I am looking for the 94V-0 fire rating certificate

1 Reply Asked by 82*******9A

Hidden and blind transitions

My project has hidden and blind transitions between layers, can you make such a board? Or do you only make through holes i......

1 Reply Asked by 34*******0A

Large Board Surcharge - What are the maximum dimensions

A PCB Gerber was submitted recently and I noticed that there was an upcharge because the board was larger than normal. Wha......

1 Reply Asked by 26*******0A

PCB Mounting Hole Positional Tolerance

I am designing a board that will be attached to a metal backplate using M2.5 bolts through PTHs (2.7 mm to 3.0 mm in diame......

1 Reply Asked by 37*******7A

Inquiry on how to plating pcb gold

Hello I need ENEPIG gold plating on the Rogers board. Can you make it?

1 Reply Asked by 77*******5A

Missing Stack-Up Option

Is the JLC04161H-2116D 4-layer stack-up option no longer available?

1 Reply Asked by 25*******7A

Stack up 4 layer 1.6mm FR4 PCB

Do you have a detailled stack-up of a standard 4-Layer FR4 1.6mm PCB? I could not find it on your website.

1 Reply Asked by 48*******4A

https:www.youtube.comwatch?v=5V7dXCTpLK0

https://www.youtube.com/watch?v=5V7dXCTpLK0 HOW CAN I MAKE THE RADIO PCB GERBER IN THIS VIDEO

1 Reply Asked by 35*******4A

Payment in Chinese yuan

Hii. Can i pay in chinese yuan for prototype pcb ? If yes, how can i do that ?

1 Reply Asked by 90*******6A

Negative layers, internal planes of PCB

Hello, I am about to send a manufacturing request for a PCB I designed in Altium which includes internal power planes. Pla......

1 Reply Asked by 97*******3A

is it possible to use the bottom side of an aluminum PCB as a ground plane?

I understand that JLCPCB only offers 1-layer aluminum PCB's, however, I am curious to know if you can apply 1mm vias from ......

3 Replies Asked by 52*******2A

Conflict mineral

Are your boards Conflict Mineral Compliant? If so, are there documents to prove this? Thank you.

1 Reply Asked by 26*******6A

Silkscreen Overlapping with Copper Pads

Hello, I use KiCAD to design my PCB boards, and in parts of my design, the silkscreen overlaps with the copper pads. But K......

2 Replies Asked by 80*******0A

Adjacent hole drilling

I wish to stack 2 x C3001542 using your footprint RJ45-TH_HYCW61-RJ45-152B How close can I physically have them together s......

1 Reply Asked by 23*******9A

Why was my shipping marked so high?

I purchased $23 worth of boards and until recently, had much cheaper shipping options. After temporary tariff changes in a......

1 Reply Asked by 92*******5A

Mu board design is irregular in shape. How much extra does that cost?

My board, approx 33x20mm is shaped as a rectangle with a triangular section missing. Is there a cost per liner mm of cut, ......

1 Reply Asked by 91*******9A

PCB - JLC3DP Q&A